Cookies del sito web Omega
Utilizziamo i cookies nel nostro sito web. Questi cookies sono necessari per consentire al sito web di funzionare correttamente. Se si continua senza modificare la propria configurazione del browser, si acconsente a ricevere i cookies dal nostro sito web. Per maggiori chiarimenti sull'utilizzo dei cookies, cliccare qui
Carrello  |  Contatto  | 
NUMERO DI TELEFONO GRATUITO (solo dall'Italia) 800 906 907
INTERNAZIONALE+39 022 333 1521
Layer N Banner

Current to Pressure (I/P) Converter


Current to Pressure (I/P) Converter - Order online | IP210

Current to Pressure (I/P) Converter - Order online

Vedi tutti i modelli qui sotto

2 anni di garanzia CE
  • Loop Power
  • Ideal for Pneumatic Control Systems
  • IP65 Sealed Case
  • Zero and Span Adjustments for Field Calibration
  • Rugged Zinc Cast Housing
  • Check our low cost IP211 I/P converter here
Valvole , regolatori e convertitori I / P - Visualizza i prodotti correlati


A "current to pressure" converter (I/P) converts an analog signal (4-20 mA) to a proportional linear pneumatic output (3-15 psig). Its purpose is to translate the analog output from a control system into a precise, repeatable pressure value to control pneumatic actuators/operators, pneumatic valves, dampers, vanes, etc. The IP210 is a loop powered instrument, which eliminates the need for an external power supply.

Accuracy: 0.5% FS, IP210. IP210A 1.5 and 2.3% (see spec sheet)
Supply Sensitivity: 0.025% span per % supply pressure change
Zero Adjustment: 5% FS
Span Adjustment: 20% FS
Operating Temp.: -5 to 160°F (-20 to 70°C)
Compensated Temp.: 15 to 140°F (-10 to 60°C)
Thermal Effects: Zero: 0.06% FS/°F Span: 0.06% FS/°F
Input Resistance: <300 Ohms
Media: Oil free clean dry air filtered to 25 µm
Recommended Supply Pressure: 25-30 psig (filtered air)
Max. Supply Pressure: 80 psig
Min. Supply Pressure: 10 psi above maximum output pressure
Air Consumption (leakage): 0.03 sfcm
Flow Rate: 10 sfcm typical
Response Time: Less than 0.5 seconds (10 to 90%step)
Failure Mode: Upon electrical failure, the signal pressure falls to bleed pressure.
Pressure Port: 1 /4 " NPTF
Electrical Conn.: DIN 43650 with screw terminals included
Housing: IP65 rated, Epoxy painted zinc die castings
Construction: Nitrile diaphragms, SS/nylon flapper, nozzle, and supply valve. Integral surface mounting bracket included.
Weight:3 lb (1.7 kg)
Ordinare(Specificare il codice prodotto)
Codice prodotto/Desc.
Consultare l'Ufficio Commerciale  
Current to pressure (I/P) converter with 2 wire 4-20 mA input and 3-60 psig output
Stock: 2 settimane
Current to Pressure (I/P) Converter with 2 wire 4-20 mA input and 3-15 psig output
Stock: 1 settimana
Current to Pressure (I/P) Converter with 2 wire 4-20 mA input and 6-30 psig output
Stock: 5 settimane
Current to Pressure (I/P) Converter with 2 wire 4-20 mA input and 2-60 psig output
Stock: 5 settimane
Current to Pressure (I/P) Converter
Tutti gli importi indicati in EUR
Nota: IP210-X120 uses 3 wire 4-20 mA connection with external 12 to 24 volt power supply. All other models are 2 wire loop powered models.
We noticed you are from the US. Visit your local site for regional offers and live support.